innovation · 24 June 2026
Inside the JISDO Innovation Lab

Every JISDO garment starts as a question in the Innovation Lab: how can this be lighter, cooler, tougher or more comfortable than the last one? This is a look inside how that question is answered, from the first fabric sample to the final garment that goes to an athlete.
The lab is not a single room. It is a way of working that combines measurement, wear testing and honest feedback. Its job is to make sure that what we say about our products is true, and that what reaches customers has been proven in conditions as close to real life as we can manage.
Airflow first
Fabrics are measured for how easily air and moisture pass through them. A fabric that lets air move helps the body shed heat and moisture, and the difference between two fabrics can be large even when they look and feel similar. We compare knit structures side by side, then take the best into wear trials to see whether the numbers match what the wearer feels.
The match is not always perfect. A fabric with excellent airflow in the lab can feel clammy against the skin, and one with modest figures can feel comfortable and fresh. That is why we never rely on a single number, and why we always follow laboratory results with wear trials.
Stretch and recovery
A garment that stretches but does not recover is a garment that bags out. Samples are pulled thousands of times and measured for how far they stretch and how completely they return. We look for fabrics that give with the body and spring back immediately, so the garment keeps its shape through a session and through a season.
We also test stretch in different directions. Many fabrics stretch well across the grain and less along it, and the way a garment is cut changes which direction matters most. Pattern makers and fabric developers work together to match the two.
Durability
Washing, abrasion and sunlight all take a toll on sportswear. We run accelerated tests so we know how a garment will look and feel after a season of real use before we put it on sale. Samples go through hundreds of wash cycles and are checked for fading, shrinkage, pilling, seam strength and loss of elasticity.
Abrasion tests rub fabric against standard surfaces under controlled pressure, simulating years of wear against pack straps, gym equipment and the ground. Colour fastness tests expose fabrics to light, sweat and washing. A garment that survives all of them has earned its place in the range.
Fit and body mapping
Fit is tested on people, not just on forms. We use body mapping to understand where the body flexes, heats and rubs, and we build patterns around that information. Testers of different shapes and sizes wear prototypes and report back on comfort, movement and how the garment behaves.
This work has changed how we design. Seam positions, panel shapes and stretch zones all come from observation of real movement. A small change, such as moving a seam by a centimetre, can remove a source of irritation that would otherwise have been noticed only after an hour of running.
Wear trials with athletes and teams
The lab works closely with athletes and teams. They train in prototypes, in all conditions, and tell us what they felt. Their feedback goes straight back to the pattern table. We value comments from beginners as much as those from elite athletes, because each shows us different problems.
Trials are structured. Testers are given specific questions about heat, rubbing, movement and durability, and asked to report at set points during and after a session. We compare their reports with the laboratory data and look for patterns.
Strip-down inspection
After wear trials, garments are taken apart and inspected. We check where seams have stretched, fabric has worn, prints have cracked and stitching has loosened. This tells us what failed, where and why, and it frequently points to problems no tester noticed.
What the lab does not do
The lab does not exist to make marketing claims. We do not publish figures we cannot repeat, and we do not describe results as better than they are. If a new fabric is not clearly better than the one it replaces, it does not go into the range.
Working with partners
We collaborate with teams, clubs and suppliers on materials and fit. If you would like to work with our lab, for example to test new fabrics or give feedback on prototypes, get in touch through the contact page and tell us what you have in mind.
A day in the lab
A typical day begins with a batch of new fabric samples, measured for weight, thickness and stretch. Mid-morning, pattern makers and fabric developers meet to discuss how a sample behaves when cut and sewn. After lunch, testers return from a run or a ride with prototypes and notes, and the team goes through their comments. By late afternoon, a change is drawn up and a revised sample is on its way to be made.
The cycle repeats many times before a garment is approved. Few ideas make it through unchanged, and many do not make it through at all. That is a sign the process is working.
What we measure, and why
Every measurement has a purpose. Weight tells us how light a garment feels. Airflow tells us how well it breathes. Stretch and recovery tell us how well it fits and keeps its shape. Abrasion resistance tells us how long it lasts. Colour fastness tells us whether it will still look good after a season. Together they give a picture that no single test can.
The people behind the work
The lab brings together fabric developers, pattern makers, product designers and test coordinators. They work with athletes, clubs and suppliers, and they are encouraged to question everything. The best ideas often come from the questions people think are too simple to ask.
If you would like to join the team, see our careers page. We are always interested in curious people who like solving practical problems.
About JISDO
JISDO Sportswear designs performance apparel for athletes and everyday movers. Media enquiries: hello@jisdo.com.


